Send the request today and stop worrying about who to call.
A boiler that shuts off and won't stay running is doing it for a reason. It might cut out after a few minutes, trip every time the thermostat calls for heat, or go dead in the middle of a cold night and leave you checking the panel for a code. In a Wisconsin winter that isn't something to sit with for long.
Most of these shutoffs trace back to a handful of things: a pressure switch that's drifting, a flame sensor that's dirty or failing, low water pressure, or a draft problem in the venting. Which one it is depends on the boiler and on what it's doing right before it cuts out, and that's not something to guess at from a search result.
Gas heat runs most homes in this state, and with power rates what they are here, nobody wants a boiler cycling on and off and wasting fuel while it tries to stay lit. A boiler that's shutting off isn't heating evenly even in the minutes it does run.
This is where a local contractor earns their keep. Someone who services boilers in Wisconsin all winter has seen this particular shutoff pattern before, knows which part tends to go first on which boiler, and can usually narrow it down fast once they're looking at the unit instead of guessing over the phone.
Send the details through below and the search is off your plate. You won't be fielding calls from a handful of companies trying to win the job. One licensed, local contractor gets matched to your request and takes it from there, and figuring out who to call stops being something you have to manage tonight.
A boiler that keeps shutting off is usually protecting itself from something wrong downstream. Low water pressure is one of the most common causes, often from a small leak somewhere in the system or a pressure relief valve that's let too much out. A failing thermocouple or flame sensor can also make it cut the gas even when the flame is lit, because the sensor isn't reading it properly anymore. Thermostat wiring and a clogged condensate line cause the same kind of shutdown. In a Wisconsin winter, none of this is something to let ride. A boiler that won't hold a cycle isn't heating your house evenly, and the parts causing it tend to get worse, not better, until someone opens the panel and finds the actual fault.
Pressure drops when it's cold
Boilers lose water pressure gradually, but the drop tends to show up first on the coldest days, when the system is working hardest and every part of it is under more strain. If yours has been low for a while, a hard freeze in January can be what finally pushes it below the cutoff and shuts the whole thing down. Check the gauge yourself before you call anyone. Most run between 12 and 15 psi cold. Below that, the boiler may be shutting off to protect itself rather than failing outright.
Flame sensors wear out slowly
A flame sensor reads the pilot or burner flame and tells the boiler it's safe to keep running. Over months of use it picks up a thin coating from the flame itself, and once that buildup is thick enough, the sensor stops reading the flame reliably even though the burner is lit and working fine. The boiler reads that as no flame and shuts down as a safety response. This kind of failure tends to get worse gradually, so a boiler that shut off once last month and now does it every day is probably on this path.
On the coldest nights here, the state averages 13°F, according to NOAA climate data. At that temperature your boiler is running close to flat out just to hold the house at a normal setting, and it's cycling more often to keep up. If the pressure is already low or the relief valve is already weak, this is the kind of night that finds it, because there's no slack left anywhere in the system. That's when a boiler that's been limping along finally shuts down and won't restart. A repair technician based in Wisconsin who works on boilers through winters like this one has likely seen your exact shutdown before, on a night just like it, and knows where to look first.
NOAA nClimDiv 1991-2020 county normals weighted by homes
A boiler that keeps cutting out on the coldest Wisconsin nights isn't something to leave until spring. Every night it runs short, the house loses ground faster than it can make up once the burner fires again, and a system that's already low on pressure or fighting a bad sensor tends to get worse under that kind of strain, not better. Figuring out which part is behind it, the pressure, the igniter, a safety switch doing its job, takes someone who works on boilers all winter in this state and knows what tends to give out when temperatures sit in the teens and below. Send the request and that part becomes someone else's job to track down. One local contractor licensed to work on your system gets it, not a handful of companies competing for the call, so you're not stuck sorting through quotes while the house keeps cooling off. That's one less thing to manage while you're watching the thermostat and waiting for the heat to hold.
What to Do Next
A boiler that keeps shutting off is almost always reacting to low pressure, a failed sensor, or an ignition problem it can't push past on its own.
The coldest nights are when these faults surface, because that's when the boiler is working hardest and has the least room for error.
A local contractor who services boilers all winter in Wisconsin has likely seen the exact fault code your unit is throwing.
Sending one request means one contractor calls, not a handful of companies competing for the job.
Catching the cause now matters more here than in milder states, since gas heat is what most homes rely on through the cold months.
The part that's failing won't fix itself, and running the system on short cycles only adds strain to whatever's already weak.
A boiler that keeps cutting out is telling you something specific, even if the panel doesn't spell it out. Pressure, a sensor, or the ignition sequence, one of those is behind nearly every case, and the pattern of when it happens points toward which one. Short cycles that show up only on the coldest nights usually mean the system was already running close to its limit before the cold made it worse.
Finding the exact cause means getting someone in front of the unit who knows what to check first. A contractor who works on boilers through a Wisconsin winter has already seen this fault more than once this season alone. They're not guessing from a manual. They know which part tends to go first on units like yours, and what a low-pressure shutdown looks like next to a failed sensor or a stalled ignition.
Sending one request puts that contractor on the job, not a list of them. You're not fielding calls from three or four companies trying to win the work, comparing quotes before anyone's even looked at the boiler. One licensed contractor, local to where you live, gets the details and takes it from there.
The boiler isn't going to sort this out on its own. Whatever's failing stays failed until someone replaces or repairs it, and every short cycle between now and then is added strain on a system that's already struggling to keep up on the hardest nights of the year.
Boiler Repair
Send one request and you're done looking
Step 1 of 3: Equipment
Tell a local repair pro what your boiler is doing.
Describe your boiler job, and a local pro who handles it gets in touch.
One request and the search for a pro is handled.
Send it once and finding someone is no longer on you.
Skip searching for a boiler pro and answer a few questions instead.
One form replaces the calls you'd make to find a boiler pro.
Only one pro gets your request, so you hear from one company.